Seat Car Trim Clips, Fixings & Fasteners

This clips are a universal replacement for seat belt buckle buttons. The clip is fitted into the centre of the belt and stops the buckle dropping t...

These star or Torx head screws are used on many SEAT cars to secure the front and rear wheel arch linings, bumpers, shields and splashguards. This ...

These black torx headed screws are used on many different SEAT models, normally to secure bumpers or wheel arch linings.

These spring clips are normally used on narrow trim strips on the inside of the vehicle. Examples include pillar trims, roof linings and tailgate l...

This long fir tree clip fits into a 7mm hole. The clip is used on many different BMW models to secure the seat backs onto the frame. It is also use...

These metal nuts are very widely used on the SEAT range to secure parts such as arch linings, undertrays, sill covers and bumper trims.

These clips are fitted to the tailgate of a vehicle. They expand to lock in position when the centre pin is inserted. The parcel shelf of the vehic...

These clips are used on various Seat models including the Ibiza, Leon and Mii. The clip is a standard 8mm push fit rivet that is used to hold panel...

Seat use two clips like this one that just vary in length. This version is 22mm long and there is also a 16mm version (Our part number FCP-0404). T...

These are very common on Audi and VW cars but are used on just a few different Seat cars. The clip is distinctive with it's sprung head and integra...

These clips are used on parts such as pillar covers and tailgate linings. The metal clip fits onto a lug on the trim. The lug and metal spring clip...

These are a simple push fit plastic rivet that expands and locks securely in position when the centre pin is inserted. The clip fits into an 8mm ho...

There are two very similar clips used by Audi, Seat, Skoda and VW on most of their models. This version is 16mm long and there is also a 22mm versi...

These screws are very common on wheel arch linings, bumpers and other shields.

These single use 7mm black fir tree clips are used by Audi on several different models. The clips are black with a 20mm diameter head. They are use...

This is a widely used yellow / orange clip found on the rubber weatherstrip seals and also on the door membrane. They are used on a number of diffe...

This is a very common part used on a wide range of vehicles all related to the Volkswagen Group. The clip is used for a variety of purposes from at...

These metal spring clips are used the hold on fascia panels and dashboard trim on the interior of several SEAT models. The clip normally fits to a ...

These metal spring clips are used to hold interior trim and fascia panels in position around the dashboard.

These standard fir tree clips are fitted to several older Honda models. The clips are used to attach interior trims and upholstery.

These black inserts are mounted into the metal bodywork. They are used to securely hold a secondary clip in position.

Very common across the entire Volkswagen Group of VW, Audi, SEAT, Skoda and Porsche. The clips are used with wheel arch liners, interior trims, qua...

These small white clips attach the ends of the door mechanism connecting rods that run between the various locks, handles and latches of the doors....

Small metal edge clip normally used by SEAT for screwing in bumpers and arch linings.

These are very widely used across the VAG group. The grommet is used on a large number of parts including around bumpers, sills, side skirts, wheel...

This sprung clip is very simple. The clip squeezes together to be fitted and expands once it is in place. It is used on a large number of different...

These locking star washers are suitable for attaching underbody noise and heat insulation. The corrosion resistant parts are used throughout the Se...

These grey trim clips were used by a few different manufacturers on older vehicles. Ford used these in particular as door card clips on the Fiesta ...

These locking star washers are suitable for attaching underbody noise and heat insulation. The corrosion resistant parts are used throughout the Se...

SEAT use these parts for interior trim such as seat base trim and access panels on the dashboard, centre console and footwell.

These are used for secure bodywork, trim panels and shields. The clip is used with a bodywork screw to hold parts in position. They are typically u...

These are a standard interior trim panel clip used on several Seat cars and across the VW group. The clips are normally used for door cards, interi...

These rear seat bench clips often fail on the Tesla Model 3 and Tesla Model Y. The clips can be replaced to prevent rattles on the rear bench seats.

These distinctive trim clips are used on some SEAT models for securing exterior trim such as bumpers.

These single use 7mm black fir tree clips are used by Seat on several different models. The clips are black with a 20mm diameter head. They are use...

These clips are used with rubber grommets to attach side skirts, sill mouldings, wheel arch flares, headlinings and other interior and exterior tri...

A very common 16mm long black metal spring clip used for attaching fascias, pillar covers and interior trims. The fastener is common on a wide rang...

A simple push fit pin rivet used on item such as bumpers, engine bay shields, undertrays and side skirts.

These aren't fitted to many Seat models but they are used on some models of the Cordoba and the Ibiza. Typically used on door cards but also someti...

These clips are used by Audi and Seat. These were fitted as Seat Exeo door card clips. Each fastener has a rubber seal attached.

The distinctive clips are used as Seat interior side trim panel and door card clips. Each fastener has a kind of sprung head which helps to reduce ...

These twist lock pins are used on some models of the Seat Exeo to attach some of the underbody shields. They are also fitted to many different Audi...

These strong and sturdy clips are used on the protective panels mounted on the underside of several Seat cars. The clips fit into a retainer and tu...

These steel fasteners are used to attach some exterior trim and body parts such as bumpers and radiator grilles.

These plastic fasteners are used on underbody shields and covers.

These unthreaded plastic nuts are used to secure protective shields and trims to the bodywork on several SEAT models.