Products

These plastic cylinder clips are used to secure the bumper and arch trims on the early models of Smart Fortwo cars.

These clips are normally used on or around the front bumpers and wheel arches. The clip is sometimes used with a screw through the middle to connec...

These clips are a simple, quick-fit clip that pushes onto a fixed, barbed or threaded stud. They are used by Hyundai and Kia to attach wheel arch l...

These clips are a simple, quick-fit clip that pushes onto a fixed, barbed or threaded stud. They are used by Kia to attach wheel arch liners or spl...

These white plastic clips have a distinctive rectangular head and are used on several Renault models. The clips are used to attach protective plast...

These white plastic trim clips have an oversize foam washer and are used to attach wheel arch trims and lower door mouldings. The clips are used on...

This clip is used all over the MK3 Hyundai Santa Fe. The clip is used to attach the wheel arch trims / flares, side body mouldings, side skirt and ...

These blue plastic trim clips are used to attach the rear wheel arch flares onto the Mk2 Toyota RAV4.

These clips are normally blue or green. Both colours are the same size and specification. We stock them in blue but they are not visible when fitte...

These black plastic fasteners are used to attach the front wheel arch trims on the Land Rover Discovery 3 and Discovery 4.

These small plastic snap fit clips are used on the wheel arch trim mouldings on some of the latest Vauxhall models including some versions of the M...

Grey plastic fasteners used by Mazda to attach the plastic trim that runs around the edge of the wheel arch. This clip is used on the Mazda CX-3 Mk...

This small white clip isn't normally sold separately by Peugeot. The trim clips are used on the front and rear wheel arch trims of the Peugeot 208 ...

These hard to find clips are not sold individually by Peugeot. They only list them with the entire wheel arch trim yet they often break if that tri...

These long white plastic trim clips are used on some models of the Jeep Wrangler to attach the external trim that runs around the edge of the wheel...

These clips are used to secure the arch flare on some versions of the Jeep Cherokee

These distinctive clips are used on the Jeep Renegade to attach the plastic wheel arch trims / flares. The green plastic fasteners have a distincti...

These small green fasteners are used on some recent Citroen models such as the C3. The plastic trim clips are used to attach the exterior trim moul...

Plastic clip that is used to retain shields and linings normally around the wheel arches. The clips can also be used as screw grommets and so are o...

These distinctive clips are used on some Ford cars and commercial vehicles. The clip head turns to unscrew and release the clip. They are normally ...

These clips are often used on the wheel arch linings of Lexus cars. The clip clicks into a square hole and locks in position but its design also th...

A common metal screw used by Audi and normally fitted on wheel arch linings, splash guards and bumpers.

These clips are used on various Seat models including the Ibiza, Leon and Mii. The clip is a standard 8mm push fit rivet that is used to hold panel...

These clips are used on several Skoda cars including the Skoda Citigo. The fastener is a standard 8mm push fit rivet that is used to hold panels an...

These plastic fasteners are used on several Volkswagen cars and vans. The fastener is a standard 8mm push fit plastic rivet. These are normally use...

These are very common on Mitsubishi cars and pick up trucks. The plastic spire-type clips are normally around the edges of the wheel arch lining wh...

These distinctive clips are used by Toyota and Lexus on a wide range of different models to attach the seal at the rear of the front wing. Please s...

A common fir tree clip used by Fiat on their cars and vans. The clip fits into an 8mm hole. A typical use is to hold the wheel arch lining or splas...

These plastic nuts are used by Fiat and Alfa Romeo. They are not threaded but have sprung tabs inside which attach onto a weld stud or threaded bar...

These metal nuts have a large collar and are used to retain the wheel arch linings, undertrays and shields in position on some Ford cars and vans.

These black plastic clips are normally used to secure wheel arch liners or underbody shields. The parts fit onto studs mounted on the body.

Fitted to at least 9 different Subaru models since 2011, this 8mm black plastic push fit trim clip is normally used on the wheel arch linings. The ...

These body screws have a captive washer and are normally used on parts such as underbody shields, wheel arch linings and to fasten body panels into...

These plastic nuts are used on some Land Rover vehicles to hold the splashguards or wheel arch linings in position. The 10mm nuts are unthreaded an...

These 8mm push fit clips have a distinctive oval shaped head that pushes in to expand the pins and hold in place. The clips are used on some Ford m...

Large headed fir tree clips that are used to hold the splash shields or wheel arch linings in place on several Nissan models. The clips have a 35mm...

These clips join the wheel arch lining or splashguard to the wing. The clips fit along the edge of the lining and then allow it to be screwed onto ...

A black plastic push nut used on many modern Kia vehicles to secure the arch linings into position. The nut is not threaded but instead has barbs t...

These plastic clips are normally used to secure wheel arch linings or other plastic trim panels in position. The clip pushes through the trim and i...

These small plastic fasteners are used on the inner wing lining on a large number of Audi vehicles. The clip is used in conjunction with a metal T-...

These small plastic fasteners are used on the inner wing lining on a large number of VW cars and vans. The clip is used in conjunction with a metal...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

This clip pushes into an 8mm square hole and is normally used to hold flexible panels such as wheel arch linings and splash guards. The centre hole...

These pin retainer clips are used on several modern Honda models to secure the wheel arch lining in position. The pin pushes into a retainer and cl...

These black plastic nuts push onto a 5mm diameter stud in the wheel arch. They are used on the front and rear arches of several Hyundai models.