Nissan Car & Van Trim Clips, Fixings & Fasteners

Very widely used clip by Nissan. Common on most models and used on bumpers, arch linings, radiator grilles, engine shields, windscreen cowls etc. T...

These clips are a perfect fit to replace any damaged or missing fasteners on the Qashqai lower door seals. The rubber strip runs along the bottom o...

These clips are a high quality replacement identical to the OE parts. Nissan use these plastic push fit rivets for a variety of uses. They can be f...

These short clips are normally used for fastening bumpers, grilles, sill moulding trims and radiator covers in place. The clips have a mottled fini...

This is a pack of 10 high quality replacement trim clips for the Nissan Qashqai (2014 on) rear door seals. The rubber door seal is at the top of th...

These 10mm push fit rivets are used on many different Nissan cars. Typical use is on bumpers, mudguards, side skirts or wheel arch linings.

These three part clips are used on the Nissan Juke Mk1 (F15). The clip is fitted to the tailgate and supports the parcel shelf.

Widely used on modern Nissan cars and vans, these clips are normally used for bumpers, grilles, undertrays and wheel arch liners. The clips are a s...

These large screw fit plastic fastenings fit into a 12mm hole. They are used on some vehicles to attach underbody shields and other large plastic t...

These clips are originally a Renault part. They are often fitted by Nissan on some of the vehicles developed jointly with Renault. They are a stron...

These clips fit on the boot of the vehicle and the parcel shelf string hangs on them. They are often lost or damaged. The clip fits into a square h...

These plastic screw grommets are used around the wheel arch lining and for wheel arch trims on a number of Nissan and Infiniti cars. They are used ...

These parcel shelf clips are used on modern Nissan models including some versions of the Note and Qashqai. The clip fits into a hole in the tailgat...

These small black plastic clips are used on some Nissan models to attach the plastic side mouldings onto the car. Each clip includes a foam sealing...

These button clips are used to secure the rubber seals in place that run around door apertures and bonnets on some Nissan vehicles.

These clips join the wheel arch lining or splashguard to the wing. The clips fit along the edge of the lining and then allow it to be screwed onto ...

These black retainers are used to secure trim in position. A common fitting location is for the windscreen cowl. This is the trim that sits below t...

This push fit plastic rivet is fitted to modern Nissan cars normally as a bumper, wheel arch or engine shield retainer. The clip is a simple expand...

Large headed fir tree clips that are used to hold the splash shields or wheel arch linings in place on several Nissan models. The clips have a 35mm...

This type of part is for mounting trims, panels or parts onto metal bodywork. The grommet fits into a hole in bodywork. The part is then aligned wi...

These 28mm round clips are used to attach the bonnet or hood insulation on many different models produced by Nissan and Infiniti. They can be fitte...

Small 6mm screw fit plastic fasteners also known as scrivets. These clips are used to fasten interior and exterior trim panels such as pillar trims...

These small clips are used on several Nissan models to secure the radiator grille in place. There are a few similar looking clips made by Nissan so...

This style of screw fit clip is typically used on loose fitting panels and these are used on some Nissan cars to attach wheel arch linings, splashg...

A simple plastic push fit rivet that goes into a 6mm hole. The centre pin pushes in to hold in place. These small and lightweight clips are normall...

Plastic screw fit rivets that expand when the centre pin is pushed or screwed in. This clip has a mottled patterned head and is used on several old...

A popular clip fitted to many different models produced by Nissan. Typically used on door cards, tailgate lining and interior fascia panels and tri...

A 6mm plastic clip used for fastening lightweight trim panels and shields.

These distinctive black plastic clips have a 10mm hexagonal head. The clips are used on some older Nissan vehicles for attaching engine undertrays,...

These distinctive clips are used to hold bonnet insulation panels in place on a wide number of Nissan models. The barbed stem of the clip fits into...

A standard black fir tree clip used by Nissan on several models. The clips are normally used for carpet lining, upholstery and trim panels in the i...

A standard push fit expanding plastic rivet which can be used for interior trim panels, dashboards, boot linings etc. This 7mm clip is used by Niss...

An 8mm screw fit plastic clip used by Nissan on some of their older models cars and vans. They are normally used to fasten splashguards, underbody ...

These small plastic push fit rivets fit into a 6mm square hole and have a rectangular collar. Typical uses includes small interior trim panels and ...

This positioning pin is used for fitting the rear bumpers to the Nissan Pathfinder, Armada and the Infiniti QX56. The pin is distinctive looking an...

These are a standard 8mm push fit plastic trim clip used on several Nissan models. The Nissan equivalent part number is 63848-01G00 or 01553-08541

A simple 8mm plastic rivet that can be used to secure trim panels. These clips require no tools to fit and quickly lock in position to secure inter...

These clips with large rectangular collars are normally used to fasten the foam impact absorption panels in place behind the plastic bumper covers.

These 8mm push fit plastic rivets are used on some models such as the Nissan Leaf and Note. The clip fits into an 8mm hole and expands to secure in...