Products

These small black plastic fasteners are used with a screw to secure parts such as wheel arch linings. They fit into an 8mm hole.

This 8mm clip is very quick and easy to install and remove. They are often used for panels where access may be required such as wheel arch linings,...

This positioning pin is used for fitting the rear bumpers to the Nissan Pathfinder, Armada and the Infiniti QX56. The pin is distinctive looking an...

Plastic screw fit rivets that expand when the centre pin is pushed or screwed in. This clip has a mottled patterned head and is used on several old...

Plastic screw fit rivets that expand when the centre pin is pushed or screwed in. This clip has a mottled patterned head and is used on several old...

This plastic automotive rivet is extremely common across the Volvo range. The clip is used for a wide variety of purposes including for bumpers, si...

These plastic trim clips are used on a few Honda models but are not very common. The clips come complete with the foam sealing washers.

This is a two-part clip that is only designed to come apart on disassembly. It is normally used on interior panels such as boot linings or pillar c...

These small clips are used on a range of Honda vehicles. They are used on some cars for splashguards but more commonly on Honda bikes and ATVs for ...

These push fit clips are used on the Fiat Fullback for the wheel arch linings.

These rectangular collared clips are used on some BMW models to attach and secure the plastic trim that runs at the bottom of the windscreen and wh...

These push fit plastic fasteners are used on many different Volkswagen cars and vans and for a wide range of purposes. They are used on the VW Tran...

These are a standard push fit plastic rivet. The centre pin is pushed in, locks in place and holds the clip in position. These are typically used o...

These 8mm plastic push fit rivets are used by BMW on engine bay shields, radiator surrounds and some interior trim panels. The clip is a standard p...

This clip is common across a lot of different manufacturers. An example fitment is that it used by Ford to attach the rear wheel arch linings on th...

Common on front and rear bumpers and underbody shields

These 8mm plastic push fit rivets are used to attach trim panels onto bodywork. They are used on some Porsche models for securing parts such as bum...

These distinctive clips are used on interior and exterior panels such as tailgate and boot linings, wheel arch splashguards and engine bay shields.

These are not widely used by Citroen but they are fitted to some models. They are typically used as wheel arch lining clips or bumper fasteners.

A simple push pin plastic trim rivet that is used on some older Peugeot models. Typical usage includes as wheel arch lining clips and bumper fasten...

Used on several Saab models, these simple push pin rivets are used to fasten bumpers, side skirts, wheel arch linings and other trim panels.

This distinctive white push pin clip expands when the centre pin is inserted. It's used on various BMW cars to secure lower sill mouldings or side ...

These blue clips are used to attach the plastic trims that run around the edges of the wheel arches on the MK1 Range Rover Evoque.

Used to fit exterior body mouldings on several different Range Rover models. The clips are normally used on side skirts, sill covers or plastic doo...

These clips are used on some models of the Vito, Metris and Sprinter. The clip is a standard 8mm push fit rivet that is used to hold panels and tri...

These small red clips are used on some Renault models to attach the wheel arch trims that run around the edge of the arch. They are distinctive due...

Nylon cable tie that is removable and fits into an 8mm hole. These parts are used by many manufacturers and a good generic part ideal for routing c...

This is a Renault door card clip that is common across their range. The clip is a two piece fastener but they are supplied and fitted pre-assembled...

A two-part clip including an 8mm retainer that fits into the bodywork of the vehicle and a press stud. The stud has a mottled patterned head and lo...

Common two-piece clip that often separates when disassembling trims or door cards. The clips are supplied and fitted in their assembled state but d...

These small black plastic fasteners are used on several Mini cars to attach the roof trim. Each clip includes a chunky foam sealing washer.

These clips are used with other plastic trim clips. This hard rubber grommet fits into a hole in the bodywork. A separate clip is inserted and the ...

These clips are used with other plastic trim clips. This hard rubber grommet fits into a hole in the bodywork. A separate clip is inserted and the ...

These are very common clips used on many different Kia cars. The clips are used to attach parts such as undertrays, windscreen cowls, side skirts, ...

These 8mm screw fit fasteners are used on some Volvo models for underbody panels and engine bay shields. The expands when the centre pin is pushed ...

These are one of the most widely used Hyundai plastic trim clips. This part is fitted to many different models and is a very common 8mm clip used o...

This is a part used by Ford and is also a good universal trim clip. The shaft is quite long and suitable for thicker panels and heavy duty uses suc...

These screw grommets are used for mounting parts and trims to bodywork on several BMW models. The clips fit into a 8mm hole and each one includes a...

These 8mm plastic push rivets are commonly used to fasten engine bay shields, bumpers or wheel arch linings.

These aren't fitted to many Seat models but they are used on some models of the Cordoba and the Ibiza. Typically used on door cards but also someti...

These are a standard interior trim panel clip used on several Seat cars and across the VW group. The clips are normally used for door cards, interi...