Products

These push fit clips are used on the Toyota GT86 to secure the front wheel arch linings and splashguards.

A common fir tree clip used by Fiat on their cars and vans. The clip fits into an 8mm hole. A typical use is to hold the wheel arch lining or splas...

These plastic nuts are used by Fiat and Alfa Romeo. They are not threaded but have sprung tabs inside which attach onto a weld stud or threaded bar...

These black plastic clips are normally used to secure wheel arch liners or underbody shields. The parts fit onto studs mounted on the body.

Fitted to at least 9 different Subaru models since 2011, this 8mm black plastic push fit trim clip is normally used on the wheel arch linings. The ...

These body screws have a captive washer and are normally used on parts such as underbody shields, wheel arch linings and to fasten body panels into...

These plastic nuts are used on some Land Rover vehicles to hold the splashguards or wheel arch linings in position. The 10mm nuts are unthreaded an...

These 8mm push fit clips have a distinctive oval shaped head that pushes in to expand the pins and hold in place. The clips are used on some Ford m...

Large headed fir tree clips that are used to hold the splash shields or wheel arch linings in place on several Nissan models. The clips have a 35mm...

These clips join the wheel arch lining or splashguard to the wing. The clips fit along the edge of the lining and then allow it to be screwed onto ...

A black plastic push nut used on many modern Kia vehicles to secure the arch linings into position. The nut is not threaded but instead has barbs t...

These plastic clips are normally used to secure wheel arch linings or other plastic trim panels in position. The clip pushes through the trim and i...

These small plastic fasteners are used on the inner wing lining on a large number of Audi vehicles. The clip is used in conjunction with a metal T-...

These small plastic fasteners are used on the inner wing lining on a large number of VW cars and vans. The clip is used in conjunction with a metal...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

This clip pushes into an 8mm square hole and is normally used to hold flexible panels such as wheel arch linings and splash guards. The centre hole...

These pin retainer clips are used on several modern Honda models to secure the wheel arch lining in position. The pin pushes into a retainer and cl...

These black plastic nuts push onto a 5mm diameter stud in the wheel arch. They are used on the front and rear arches of several Hyundai models.

These black metal screws are the most common size used by Honda to secure wheel arch linings and splashguards. The screws are high quality parts id...

These metal screws are used on some Porsche models for securing the wheel arch linings, mudguards and under body shields into position.

Used on many modern Renault vehicles from new and also a supersession for parts used on older models such as the Renault 5. These clips push onto a...

These small plastic clips fit onto threaded or barbed studs in the wheel arch. The clip push down over the stud and scures the arch lining in posit...

These distinctive clips are used to hold and secure the splash guard liner around the wheel arch.

These star or Torx head screws are used on many SEAT cars to secure the front and rear wheel arch linings, bumpers, shields and splashguards. This ...

Fitted to several Mitsubishi models, these clips are used for multiple purposes. They are found on wheel arch linings, bumpers, splashguards and in...

These clips are pushed onto on a metal bodywork stud. They are normally used on plastic parts such as arch linings, splashguards or shields.

Used on several Mini car models, these plastic screw to fit clips are used on large trim panels such as bumpers, sill covers and underbody shields....

These screws each have an 18mm captive washer. The screws are normally used for securing parts such as arch liners, splashguards or undertrays.

These small black clips are used on some Honda models to attach the plastic trims that run around the edges of the wheel arch. This clip has Honda ...

These plastic nuts are used on threaded studs that are normally welded to the bodywork of the vehicle. The wide collar acts like a washer and the p...

These wide collar screw fit clips are normally used for fitting loose panels or upholstery and carpeted trims.

This plastic nut is used on the underbody shields and trim panels of many different Skoda models. The part fixes onto the metal stud on the unders...

These are very common on modern Audi cars for underbody shields, covers and splashguards. The nuts are threaded and fit onto studs already attached...

These are very common on modern VW cars and vans. The nuts are almost always used to attach underbody shields and insulation.

These black clips are used to ensure the front window stays properly aligned as it goes up and down. The clip is held in by a single pin and can be...

These small edge clips are used on some Ford models to secure the plastic windscreen cowl that covers the wiper motor and linkage at the bottom of ...

The small moulding clips are normally used by BMW to secure the plastic windscreen cowl in position. This is the plastic cover that runs along the ...

The E34 5-series, E32 7-series and the Z1 roadster all use these clips to attach and hold the windscreen cowl. This plastic trim, also known as the...

A large headed, screw fit fastener used on the lower windscreen trim or scuttle panel cover on several Skoda models.

These distinctive plastic fasteners are used to secure the windscreen cowl in position on many Subaru models.

These push fit clips go into a 6.5mm hole. They have rectangular shaped collar. The clips are used by Volvo to secure the windscreen cowl or scuttl...