Produits

These plastic spacers / washers are used with metal clamps to secure underbody shields into position. They are very common across the VW group.

These plastic washers are fitted to the underside of several modern Skoda vehicles where heat shields are held on by metal star washers. The plasti...

These plastic spacers / washers are used with metal clamps to secure underbody shields into position. They are very common across the VW group.

These are used on the engine undertray and underbody shields of several Skoda models including the Superb.

A metal screw with 18mm washer that is used for securing parts such as engine undertrays, splashguards and wheel arch liners.

These black brackets can be used to mount trim panels onto vehicle bodywork and keep the fixings hidden.

These are a very common interior trim panel screw used on a wide range of SEAT cars. Typical uses include around the doors, centre console, dashboa...

These small black plastic trim clips are used on the VW T5 and T6 to attach the surround to the sliding door interior handle. There are two clips u...

These arrowhead plastic clips are used to secure rubber seal in position. There are commonly used on the windscreen cowl and some door seals.

A push fit plastic clip that is used to secure the weatherstrip in position on some older Audi vehicles.

These clips are often used on the wheel arch linings of Lexus cars. The clip clicks into a square hole and locks in position but its design also th...

A common metal screw used by Audi and normally fitted on wheel arch linings, splash guards and bumpers.

A common fir tree clip used by Fiat on their cars and vans. The clip fits into an 8mm hole. A typical use is to hold the wheel arch lining or splas...

These plastic nuts are used by Fiat and Alfa Romeo. They are not threaded but have sprung tabs inside which attach onto a weld stud or threaded bar...

These black plastic clips are normally used to secure wheel arch liners or underbody shields. The parts fit onto studs mounted on the body.

These body screws have a captive washer and are normally used on parts such as underbody shields, wheel arch linings and to fasten body panels into...

These plastic nuts are used on some Land Rover vehicles to hold the splashguards or wheel arch linings in position. The 10mm nuts are unthreaded an...

Large headed fir tree clips that are used to hold the splash shields or wheel arch linings in place on several Nissan models. The clips have a 35mm...

A black plastic push nut used on many modern Kia vehicles to secure the arch linings into position. The nut is not threaded but instead has barbs t...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These black plastic nuts push onto a 5mm diameter stud in the wheel arch. They are used on the front and rear arches of several Hyundai models.

These black metal screws are the most common size used by Honda to secure wheel arch linings and splashguards. The screws are high quality parts id...

These metal screws are used on some Porsche models for securing the wheel arch linings, mudguards and under body shields into position.

These small plastic clips fit onto threaded or barbed studs in the wheel arch. The clip push down over the stud and scures the arch lining in posit...

These clips are pushed onto on a metal bodywork stud. They are normally used on plastic parts such as arch linings, splashguards or shields.

These screws each have an 18mm captive washer. The screws are normally used for securing parts such as arch liners, splashguards or undertrays.

These black clips are used to ensure the front window stays properly aligned as it goes up and down. The clip is held in by a single pin and can be...

These small edge clips are used on some Ford models to secure the plastic windscreen cowl that covers the wiper motor and linkage at the bottom of ...

These distinctive plastic fasteners are used to secure the windscreen cowl in position on many Subaru models.

These push fit clips go into a 6.5mm hole. They have rectangular shaped collar. The clips are used by Volvo to secure the windscreen cowl or scuttl...

These push fit plastic buttons click into position and fasten the windscreen cowl and engine shields into position. This type is used on several Ho...

This clip is used at the lower end of the windscreen side trim. They are fitted to the Mk1 Volvo V60 and the Mk2 S60.