Produkte

A push fit plastic clip that is used to secure the weatherstrip in position on some older Audi vehicles.

These blue plastic trim clips are used to attach the rear wheel arch flares onto the Mk2 Toyota RAV4.

These small plastic snap fit clips are used on the wheel arch trim mouldings on some of the latest Vauxhall models including some versions of the M...

This small white clip isn't normally sold separately by Peugeot. The trim clips are used on the front and rear wheel arch trims of the Peugeot 208 ...

These hard to find clips are not sold individually by Peugeot. They only list them with the entire wheel arch trim yet they often break if that tri...

These long white plastic trim clips are used on some models of the Jeep Wrangler to attach the external trim that runs around the edge of the wheel...

These black fir tree clips are used to attach and secure the wheel arch flares and arch trims on the front and rear of some Ford models. Vehicles u...

These clips are used to secure the arch flare on some versions of the Jeep Cherokee

These clips are often used on the wheel arch linings of Lexus cars. The clip clicks into a square hole and locks in position but its design also th...

These push fit clips are used on the Toyota GT86 to secure the front wheel arch linings and splashguards.

A common fir tree clip used by Fiat on their cars and vans. The clip fits into an 8mm hole. A typical use is to hold the wheel arch lining or splas...

These plastic nuts are used by Fiat and Alfa Romeo. They are not threaded but have sprung tabs inside which attach onto a weld stud or threaded bar...

These black plastic clips are normally used to secure wheel arch liners or underbody shields. The parts fit onto studs mounted on the body.

These plastic nuts are used on some Land Rover vehicles to hold the splashguards or wheel arch linings in position. The 10mm nuts are unthreaded an...

Large headed fir tree clips that are used to hold the splash shields or wheel arch linings in place on several Nissan models. The clips have a 35mm...

A black plastic push nut used on many modern Kia vehicles to secure the arch linings into position. The nut is not threaded but instead has barbs t...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These two part push fit clips are made from metal and plastic. The clips are typically used on parts such as wheel arch linings or for other trim p...

These black plastic nuts push onto a 5mm diameter stud in the wheel arch. They are used on the front and rear arches of several Hyundai models.

These distinctive plastic clips fit into a square hole and are normally used on the wheel arch linings.

These small plastic clips fit onto threaded or barbed studs in the wheel arch. The clip push down over the stud and scures the arch lining in posit...

These clips are pushed onto on a metal bodywork stud. They are normally used on plastic parts such as arch linings, splashguards or shields.

These small white snap fit clips are used on several Peugeot models. They are used on the Peugeot 208 (2019 on) to attach the exterior wheel arch t...

These white plastic trim clips fasten onto the body of the Volvo C30. The ball of the clip is on the outside and allows for the arch trim to be cli...

These simple white plastic guide runners are used to guide the door windows as they slide up and down. The clips fit inside the frame, underneath t...

These simple white plastic guide runners are used to guide the door windows as they slide up and down. The clips fit inside the frame, underneath t...

These black clips are used to ensure the front window stays properly aligned as it goes up and down. The clip is held in by a single pin and can be...

These distinctive plastic fasteners are used to secure the windscreen cowl in position on many Subaru models.

These grey receiver clips are used on several Fiat models including some versions of the Palio, Ducato, Doblo and Fiat 500. The clip is used to sec...

These push fit clips go into a 6.5mm hole. They have rectangular shaped collar. The clips are used by Volvo to secure the windscreen cowl or scuttl...

These push fit plastic buttons click into position and fasten the windscreen cowl and engine shields into position. This type is used on several Ho...

This clip is used at the lower end of the windscreen side trim. They are fitted to the Mk1 Volvo V60 and the Mk2 S60.

These yellow plastic clips are used to attach the trim or moulding that runs on the side of the windscreen. This part is used on several different ...

These distinctive clips are metal and plastic and are used to attach the trim that runs on the side of the windscreen. This clip is fitted to sever...

These are small white plastic clips used to secure the tweeter cover and wing mirror trim to the inside of the door . They are used on many differe...